T12 Soldering Iron Station OLED Temperature Controller w/ 9501 Handle for HAKKO

Description

elecbuy
Home
Description
Payment
Shipping
Terms of sale
About Us
T12 Soldering Iron Station OLED Temperature Controller w/ 9501 Handle for HAKKO
Package include:
1 x OLED temperature controller
1 x 9501 handle
1 x T12-K tip
1 x 1m 4pin Cable
1 x 4pin Connector
1 x Tin&rosin kit
Note:
This is a DIY kit, not finished product,you need to assemble it yourself.
1. Follow the instructions as below, pay attention to insulation, static electricity, and grounding.
2. Before power-on test, carefully check whether the wiring is correct, whether it is soldered or short-circuited.
3. Power supply 12-24VDC
4. Power supply voltage and current, please refer to the following table:
Installed Note:
1. Strictly reference shop tutorials, well insulated and grounded against static electricity.
2. Before power test, carefully check the wiring is correct, whether Weld and short, full power test machine after confirmation.
3. connect 12-24V DC, if received more than 20V power supply,2017 new style product don't need to remove anything!
4. When you configure the power supply voltage and current requirements themselves refer to the following table:
Power (third column) is determined by the voltage (first column), as long as the current reaches the minimum current (second column).
Measuring Machine normal, lights and display status:
1. Unplugged T12 tip, turn the light flashed off, show SER, 1 seconds after the display 500.
2. T12 plug tip, boot light uniform flashing, indicating rapid heating from room temperature generally show the set temperature to rise, approaching the set temperature, strobe lights. Indicator is not flashing or intermittent flashes, indicating that the tip temperature reaches the set temperature or alternating temperature compensation.
When measuring machines on display digital bounce questions:
Because with the new T12 tip, the tip inside the heater did not burnt, it will be just a little jump start with warm, generally do not need special treatment, the natural use of 1-2 days basically not bounce up. If you need effective immediately, the general recommendations of the temperature to 350 ?-380 ?while heating to the point of tin iron head, burning off after 4-5 minutes, until the tip to cool before you can reboot! (1 no action can be repeated 2-3 times)
Payment
We accept PayPal only.
Shipping
1.Items are shipped from china.we will send out within 1 bussiness day after receive the payment.
2.We only ship to ebay confirmed address. So before bidding,  please kindly verify your ebay address.
3.
Shipping to USA takes 8-18 days in normal condition by E-packet with tracking number.
Shipping to most other countries takes about 12-30 days via Economy Int'l Airmail.
Less than , without free tracking number,if you request tracking number,please send ebay message to us.
Over ,with tracking number free.The shipping time depends on your location and local postal service,as well as the weather condition along the shipping,sometimes may take longer,.please send ebay message to us if you didn't get your package.
4.Express shipping: Extra  -- will be charged for the first 500 grams for most countries. Send ebay message to us if  you need this service.
Terms of sale
1.If you are not satisfied when you receive your item, please return it within 30 days for a replacement or money back.   Please send ebay message to us before you return it.
2.If item is defective in 30 days, We will send you a replacement without extra charger, or offer refund after we receive the defective item.
3.If item is defective after 30 days, you can still send it back to us. We will send you a new one after receiving the defective item. But you have to pay the extra shipping fee.
About us
We are honest seller and do our best to serve you.
So if you have any concerns,please don’t hesitate to send ebay message to us.